We are not responsible for possible damage caused by overclocking. Page 9. Just launch this tool and save the new BIOS file to your USB flash drive, floppy disk or hard drive, then you can update your BIOS only in a few clicks without prepar- ing an additional floppy diskette or other complicated flash utility. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Do not force to insert the CPU into the socket if above situation is found.
Page 15 PnP cap to assist in removal. It is recommended to use the cap tab to handle and avoid kicking off the PnP cap. This cap must be placed if returning the motherboard for after service.
Ensure that the CPU and the heatsink are securely fastened and in good contact with each other. Step 1. Unlock a DIMM slot by pressing the retaining clips outward. Step 2. Page Jumpers Setup 2-pin jumper see p. The data in CMOS includes system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply.
Page 20 Please short pin2, pin3 for OC jumper. Otherwise, the CPU may not work properly on this motherboard. Please refer to below jumper settings. Please short pin2, pin3 for OC jumper. Otherwise, the CPU may not work Page 22 HDA to function correctly. Locate Pin1 and the two orientation key notches. For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket.
Carefully place the CPU into the socket by using a purely vertical motion. Verify that the CPU is within the socket and properly mated to the orient keys. Use your left hand index finger and thumb to support the load plate edge, engage PnP cap with right hand thumb and peel the cap from the socket while pressing on center of PnP cap to assist in removal.
It is recommended to use the cap tab to handle and avoid kicking off the PnP cap. This cap must be placed if returning the motherboard for after service.
Rotate the load plate onto the IHS. While pressing down lightly on load. Secure load lever with load plate tab under retention tab of load lever.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. User Manual Version 1. All rights reserved. Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.
Contents 1 Introduction Please refer to page 19 for proper jumper settings. This motherboard supports Untied Overclocking Technology. This motherboard supports Dual Channel Memory Technology.
Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 16 for proper installation.
The maximum shared memory size is defined by the chipset vendor and is subject to change. Do not over-tighten the screws!
Doing so may damage the motherboard. Step 1. Open the socket: Step Step 2. Hold the CPU by the edges where are marked with black lines. Step 3. Remove PnP Cap Pick and Place Cap : Use your left hand index finger and thumb to support the load plate edge, engage PnP cap with right hand thumb and peel the cap from the socket while pressing on center of PnP cap to assist in removal.
Step 4. Close the socket: Step While pressing down lightly on load plate, engage the load lever. You can only view or download manuals with. Sign Up and get 5 for free. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again.
To improve heat dissipation, remember to spray thermal grease between the CPU and the heatsink when you install the PC system. EuP, stands for Energy Using Product, was a provision regulated by European Union to define the power consumption for the completed system. According to EuP, the total AC power of the completed system shall be under 1. For EuP ready power supply selection, we recommend you checking with the power supply manufacturer for more details. Take note of the following precautions before you install motherboard components or change any motherboard settings.
Unplug the power cord from the wall socket before touching any component. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.
Hold components by the edges and do not touch the ICs. Whenever you uninstall any component, place it on a grounded antstatic pad or in the bag that comes with the component. When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws!
Doing so may damage the motherboard. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged. Step Disengaging the lever by depressing down and out on the hook to clear retention tab. Rotate the load lever to fully open position at approximately degrees. Rotate the load plate to fully open position at approximately degrees. Locate Pin1 and the two orientation key notches.
For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket. Carefully place the CPU into the socket by using a purely vertical motion. Verify that the CPU is within the socket and properly mated to the orient keys. Use your left hand index finger and thumb to support the load plate edge, engage PnP cap with right hand thumb and peel the cap from the socket while pressing on center of PnP cap to assist in removal.
It is recommended to use the cap tab to handle and avoid kicking off the PnP cap. This cap must be placed if returning the motherboard for after service. Rotate the load plate onto the IHS. While pressing down lightly on load. Secure load lever with load plate tab under retention tab of load lever. For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink.
Step 1. Apply thermal interface material onto center. Otherwise, it will operate at single channel mode. If you install only one memory module or two non-identical memory modules, it is unable to activate the Dual Channel Memory Technology. Please make sure to disconnect power supply before adding or removing DIMMs or the system components. Step 2. The DIMM only fits in one correct orientation. Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully.
Before installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation. Remove the bracket facing the slot that you intend to use.
Keep the screws for later use. Align the card connector with the slot and press firmly until the card is completely seated on the slot. The data in CMOS includes system setup information such as system password, date, time, and system setup parameters.
To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. The default setting short pin1 and pin2 is EuP enabled. If you want to disable this power saving function, you may short pin2 and pin3. Please short pin2, pin3 for OC jumper. Otherwise, the CPU may not work properly on this motherboard. Please refer to below jumper settings. Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors.
Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Note: Please refer to the instruction of your IDE device vendor for the details. Please connect the black end of SATA power cable to the power connector on each drive. Then connect the white end of SATA power cable to the power connector of the power supply. Please follow the instruction in our manual and chassis manual to install your system.
Enter Advanced Settings, and then select Chipset Configuration. Enter Windows system. To activate the front mic. To install the drivers to your system, please insert the support CD to your optical drive first.
0コメント